Tkelly
@tkelly-CKF896 Member
- Member since
- Joined
- Last active
- Active
- Member number
- Member #34,293
- Posts
- 0
- Replies
- 26
- Reactions
- 0
- Active days
- 0
Contributions
Last 12 months
0 contributions
- Active days
- 0
- Longest run
- 0 days
- Current run
- 0 days
Trophies
Featured trophies
0 / 8
Swipe or scroll to see more trophies
-
Replied #Threads
o-rng gland design
First thing is whether you need O ring for static or dynamic application. Then only you can select O ring. Cross section can depend upon how...
-
Replied #Threads
motor coupling to rack & pinion
Ideally, Motor alongwith pinion should be fixed & steady and rack should move up & down. Best solution can be given if you provide some sketch...
-
Replied #Threads
Plate Type Heat Exchangers
Hi, First thing is after how long you are over hauling/servicing plate HE. If it is quite long time then there is possibility that while servicing...
-
Replied #Threads
Braking System Design help wanted...
Re: Design help wanted... I do not understand how electro magnet will work here. Please explain. Tom <a href="https://www.indovance.com" target="_blank" rel="nofollow noopener n...
-
Replied #Threads
conveyor HELP!!
You have mentioned,conveyor will be used for book ransportation. But please mention:- * What is the length ? * Whether it is horizontal or vertical ?...
-
Replied #Threads
How convergent- divergent nozzle work?
For the convergent-divergent nozzle the calculation from the inlet to the throat (convergent) is usually an expansion to sonic conditions. From convergent to divergent the flow...
-
Replied #Threads
Hydraulic Power pack
Are you looking for a company who makes hydraulic power pack or looking for a candidate ? Please elaborate giving your area of working. Tom Kelly...
-
Replied #Threads
Have you heard of AIRLESS TYRES??
Good innovation. This will save lot of money. According to me hardness of the tyres will be different for different types of vehicles. Is it correct...
-
Replied #Threads
Braking System Design help wanted...
Re: Design help wanted... Arrangement in model diagram looks ok but confirm the following. 1) Middle rod on which load slides will have square threads and...
-
Replied #Threads
fabrication project necessary
First elaborate on this fabrication project. Should it involve sheet metal, bending, shearing, welding? If it is the case, then take project for manufacturing small electrical...
-
Replied #Threads
rack and pinion calculations
Zorif is right. I also suggested same thing. From the load you can decide module od DP ( in inches). Once you know the module, you...
-
Replied #Threads
design of shafts
First question, how you decided the motor power without any calculations? I suggest you to speak to speed reducer manufacturer(worm gear box manufacturer) with available data....
-
Replied #Threads
rack and pinion calculations
There is formula for calculating the pitch, but it also requires the technical data as written earlier. Tom <a href="https://www.indovance.com" target="_blank" rel="nofollow noop...
-
Replied #Threads
Mass moment of inertia
Mass moment of inertia = M x (K)2 x C M = Mass K = Radius of gyration C = constant Tom <a href="https://www.indovance.com" target="_blank" rel="nofollow...
-
Replied #Threads
composites in aluminium as base
There are different types of Alluminum alloys depending upon application. You can also get the data at #-Link-Snipped-# Tom <a href="https://www.indovance.com" target="_blank" re...
-
Replied #Threads
rack and pinion calculations
Without knowing the load to be moved, you can not decide the pitch of Rack & Pinion. Also mention the distance of the rack you required...
-
Replied #Threads
calculating torque and power
Assume this shaft is rotating along with the given load. In that case above formulae is correct. But for calculating angular velocity,you should know the RPM...
-
Replied #Threads
Radil blowers
There is no any software for designing. Softwares are only for modelling. For modelling one can use Solidworks, ProE, Catia, etc. Tom <a href="https://www.indovance.com" target="...
-
Replied #Threads
Software for mechanical engineers
Since you are a student, I would suggest to get aquainted with 2D AutoCAD and after that can easily complete Solid Works. Solid Works is easy...
-
Replied #Threads
How many carburettors are used in v-engines?
It depends on number of cylinders. For left and right cylinders, there is pair of corburettors. Tom <a href="https://www.indovance.com" target="_blank" rel="nofollow noopener nor...
-
Replied #Threads
Free hvac lessons
Very nicely, compilled & usefull data for HVAC tech. people. Tom <edited>
-
Replied #Threads
Design two stage gear box with helical gears
To design gear box one should know input & output parameters. Tom <a href="https://www.indovance.com" target="_blank" rel="nofollow noopener noreferrer">CAD Outsourcing Services...
-
Replied #Threads
which is beter catia, pro-e etc..
Do not go for Pro-E, as detailing is difficult in this. Solid works is very good and user friendly for solid modelling and Catia is good...
-
Replied #Threads
Hardness Test
What hardness you would like to test. For rubber, different tester is used. i.e. for measuring Shore "A" hardness. For metal Rockwell or brinell hardness tester...
-
Replied #Threads
Automatic motorcycle sidestand removing system
Fit a micro limit switch at the side stand & indication on dash board. That means unless side stand is removed , indication will not get...
-
Replied #Threads
shaft design
Shaft design procedure can be given but before that following parameters should be known. 1) what is medium for blower i.e. cold air, hot air, air...
Activity by month
Where Tkelly contributes
-
#Threads 26 · 100%
Highlights
- Reactions per contribution
- 0.0
- Best answers
- 0
- Member for
- 17 years