PRADIP CHAKRABORTY
@pradip-MzE4HZ Member
- Member since
- Joined
- Last active
- Active
- Member number
- Member #120,134
- Posts
- 89
- Replies
- 40
- Reactions
- 0
- Active days
- 1
Contributions
Last 12 months
1 contribution
- Active days
- 1
- Longest run
- 1 day
- Current run
- 0 days
Most active on Fridays.
Trophies
Featured trophies
0 / 8
Swipe or scroll to see more trophies
-
-
Replied #Threads
PITOT TUBE AND VENTURI METER
PRAD CHAKRABORTYCan anybody provide me the details of the working principle details of Pitot Tube and Venturi meter.a lot of thanx
-
Replied #Threads
RELEVANT ANALYSIS ON MECHANICAL EQUIPMENT
varun kumar K AYes, do you think is it structural analysis? If you send me complete problem and drawing.Yeah,I'm sending you the drawing shortly
-
-
Replied #Threads
What is Surge in Springs?
jaspal rautelaI am Jaspal and I have this question about machine designs. what is meant by surge in spring? Could some mechanical engineers of the community...
-
Replied #Threads
Youth Participation In Politics - Will it change anything?
There are various action training schools situated within our country to nurture tomorrows talents. Pune film institute has produced several actors and actresses ,who are now...
-
Replied #Threads
LOAD CARRYING CAPACITY OF INDIAN STANDARD STEEL ANGLE
Sumukhm39Roughly 10kN compressive & 30kn tensile for standard Fe250 grade. May change depending on the end conditions and connection.thanks a lot for this valuable information
-
Replied #Threads
STAINLESS STEEL
Anku2993Dear, First of all, i don't know exactly about CCD, i think it is something related to transferring electric charge from one place to other where...
-
-
Replied #Threads
TORQUE CALCULATION ON A CIRCULAR DISC
ok si PRAD CHAKRABORTYit might be the radius of the disc?r
-
Replied #Threads
TORQUE CALCULATION ON A CIRCULAR DISC
PRAD CHAKRABORTYit might be the radius of the disc?
-
-
Replied #Threads
TORQUE CALCULATION ON A CIRCULAR DISC
PRAD CHAKRABORTYA disc of dia 300 mm and thickness of 5 mm made of mild steel.It has to be rotated by a motor at a rpm...
-
Replied #Threads
STAINLESS STEEL
Anku2993Dear, Be specific about your question. You are asking for SS, But also at the same time you want high tensile resistance. First of all, be...
-
Replied #Threads
FACTOR OF SAFETY OF EOT CRANE..
Anku2993Dear, In industry, usually F.O.S considered for EOT Cranes is 5. And regarding Formula, F.O.S formula is same as usual(not specific for EOT). That is, F.O.S.=allowable...
-
Replied #Threads
EFFECT ON MACHINING ON INDIAN STANDARD IRON ANGLE
A.V.RamaniThe strength of steel does not change. But at the cross section where there is a slot or hole, the area of the channel gets reduced....
-
-
Replied #Threads
EFFECT ON MACHINING ON INDIAN STANDARD IRON ANGLE
A.V.RamaniThere is no such animal. It is not possible to have an equal angle 50mm x 50 mm and a thickness of 50 mm. Strength properties...
-
Replied #Threads
USE OF CADMIUM PLATED FASTENERS
Why cadmium plated fasteners are used in aeronautical fabrication?
-
Replied #Threads
Is it better to learn Autocad, CATIA, SolidWorks from First Year
BEFORE LEARNING DESIGN SOFTWARE,ONE SHOULD HAVE THE BASIC KNOWLEDGE OF ENGINEERING DRAWING AND DESIGN
-
Replied #Threads
Difference between pump and compressor
N.SACHINwhen you inflate a car tyre machine is called compressor, but when u do same for bicycle tyre it is called pump. Why? What is the...
-
Replied #Threads
TORQUE CALCULATION
nooneperfectwhat power source ur using?? motor h.p.??0.5 HP MOTOR
-
Replied #Threads
WIND LOAD ON FENCE
A.V.RamaniThe material of the fence is largely irrelevant for wind loads. What is the geometry of the fence? If you are a student, your university may...
-
-
-
Replied #Threads
INVESTMENT CASTING
A.V.RamaniWe investigated investment casting of chrome-cobalt alloys for some medical device development. Here are some links: Key steps in investment casting: #-Link-Snipped-#...
-
Replied #Threads
COMPUTER INTEGRATED MANUFACTURING(CIM)
Kaustubh KatdareYour question is not clear. What exactly are you looking for?WHAT IS MEANT BY COMPUTER INTEGRATED MANUFACTURING?
-
-
Replied #Threads
HOW TO UPDATE AUTO CAD SOFTWARE?
Kaustubh KatdareHow are you planning to update it? Using a DVD of the new version of you've downloaded a new version of the software?PLEASE SUGGEST,WHICH IS...
-
Replied #Threads
TURN BUCKLE
WHAT IS THE FUNCTION OF A TURN BUCKLE IN CASE OF FORK MOUNTING TELESCOPE? ARE THE THREAD SIZES ON BOTH SIDES OF A TURN BUCKLE IDENTICAL?
Activity by month
Busiest month: March 2026
Where PRADIP contributes
-
#Threads 128 · 99%
-
#Discussions 1 · 1%
Highlights
- Reactions per contribution
- 0.0
- Best answers
- 0
- Member for
- 14 years