maxz
@maxz-iHZPgv Member
- Member since
- Joined
- Last active
- Active
- Member number
- Member #32,630
- Posts
- 11
- Replies
- 37
- Reactions
- 0
- Active days
- 0
Contributions
Last 12 months
0 contributions
- Active days
- 0
- Longest run
- 0 days
- Current run
- 0 days
Trophies
Featured trophies
0 / 8
Swipe or scroll to see more trophies
Recent contributions
-
Posted #Threads
Racks and Pinions
Dear CEIan, I have been searching alot on internet this few weeks, but i could hardly get some idea on how to determine the tooth of...
1 reply -
Replied #Threads
Car Brake System~!!!! How to improve it?
well~ for my project, i just studies on the design of the braking plate and the material of it only. as i mentioned, no sponsors. so...
-
Replied #Threads
Car Brake System~!!!! How to improve it?
I see.... but i think there's some alternative way to use on the improvement.. since i graduated, i never look on the research already. Moreover, there...
-
Replied #Threads
Car Brake System~!!!! How to improve it?
Thank you again for all. I'm here and yes, i have graduated from my University.
-
Posted #Threads
Vertical Force Calculation
Dear CEian, I would like to ask weather there is a possible chance tat i can calculate vertical forces rather than horizontal force? by my understanding,...
-
Posted #Threads
Dynamic Simulation by Inventor 2010
Hi CEians~ I've been looking throughout the internet for Dynamic Simulation tutrials but have failed to find 1. can anyone plz send me some links for...
1 reply -
Replied #Threads
Car Brake System~!!!! How to improve it?
Finally i had a break through and my project were a success. I had a Grade B on my Project and i'm very proud and thank...
-
Posted #Threads
Ansys Crack
How do i crack my ansys?? it seems like my host not connected after i install the license...
-
Replied #Threads
Stress Analysis Using Autodesk Inventor 2010
Dear Juma... What happen with inventor 2010??? I do all the steps but i couldnt get wat u did in here... it shows only displacement and...
-
Replied #Threads
Stress Analysis Using Autodesk Inventor 2010
Omg Juma~!! U're really Helpful... and this thing i saw it before in Inventor.. and i was like wtf was this... so i doesnt care much...
-
Replied #Threads
Stress Analysis Using Autodesk Inventor 2010
thx juma~!! It would be appreciate if u write it step by step how to set those configurations.
-
Replied #Threads
Circular Plate Bending Moment and Stress
btw wat is design accelerator formulas??? where can i get it?
-
Replied #Threads
Stress Analysis Using Autodesk Inventor 2010
Dear Juma, I have roughly sketch the plate i wanted to analyst... I hope this could help for you, so that u could help me out...
-
Replied #Threads
Stress Analysis Using Autodesk Inventor 2010
I'll post the picture soon... allow to help me out.. thx so much~!!
-
Replied #Threads
Stress Analysis Using Autodesk Inventor 2010
Yesss... Juma~!! this is exactly wat i need... a displacement and stress analysis...
-
Replied #Threads
Circular Plate Bending Moment and Stress
For the manual calculation part i'm done, and the result is quite satisfied... But i need to compare it with my simulation testing using Inventor 2010......
-
Replied #Threads
Car Brake System~!!!! How to improve it?
it is possible if were to implement ABS to my design as well... Currently i were to test on the friction efficiency between existing and my...
-
Posted #Threads
Stress Analysis Using Autodesk Inventor 2010
Hello to all CEans, I'm Chea from Msia, currently doing Final Semester of Mechanical Engineering. I kinda noob in using Inventor as i need to test...
16 replies -
Replied #Threads
Circular Plate Bending Moment and Stress
Dear Juma~!!! Your guides is very useful to me. being finding this for a long time. Never know it can be found in Autodesk Inventor Handbook....
-
Posted #Threads
Circular Plate Bending Moment and Stress
Dear CEians, I had a small project going onto my final semester subject. Its a about a Circular Plate attached to the shaft spinning at 1280rpm...
7 replies -
Replied #Threads
COMSOL Error 7094???????
Thx alot... it help. yeah. my memory is out~!!! need to upgrade my Ram
-
Posted #Threads
COMSOL Error 7094???????
GUys.... wat does it mean by Error 7094 in Comsol Multiphysics????? Please Help~!!! I was using the General Heat Transfer module to test out my material......
3 replies -
Replied #Threads
Car Brake System~!!!! How to improve it?
No comments on my idea for the brake?????? wierd~!!!!
-
Posted #Threads
How do I handle this? Need your help!
Differentialmaxzdear bro~! i have doubts again for my fyp. its quite annoying becoz i meet my supervisor on my project today and he told me that...
2 replies -
Replied #Threads
Car Brake System~!!!! How to improve it?
Its been a while i left this post death~!! I'm back and wanted to post some of the pictures in here. i Guess i will receive...
-
Posted #Threads
Improve on Clutch Life Span
Dear Ceans~!!!! How to imporve the Clutch Life Span to avoid the transmission jammed in the middle of the journey to back home or long distance...
2 replies -
Replied #Threads
Car Brake System~!!!! How to improve it?
The shape would be on its way. currently i still stucking on my project idea. as my college have damn a lot of student were doing...
-
Replied #Threads
Car Brake System~!!!! How to improve it?
It is true. Increase Surface area for friction is much likely better than the existing 1. the existing area surface is limited. so i think is...
-
Replied #Threads
How would you modify a bicycle to make it more efficient?
Hurm~!!!! I think the body of the frame have to be mobs a bit by mobbing it with some angle to reduce the air frictions against...
-
Replied #Threads
Car Brake System~!!!! How to improve it?
Nah. Tat Info is from my crap supervisor telling that drum is more efficient. i disagree with him as well.. and ya magnectic brake have some...
Activity by month
Where maxz contributes
-
#Threads 48 · 100%
Highlights
- Reactions per contribution
- 0.0
- Best answers
- 0
- Member for
- 17 years