pratik20990
@pratik20990-Y0V1iW Member
- Member since
- Joined
- Last active
- Active
- Member number
- Member #42,587
- Posts
- 11
- Replies
- 11
- Reactions
- 0
- Active days
- 0
Contributions
Last 12 months
0 contributions
- Active days
- 0
- Longest run
- 0 days
- Current run
- 0 days
Trophies
Featured trophies
0 / 8
Swipe or scroll to see more trophies
Recent contributions
-
Posted #Threads
charging of batteries
I have four 3.7V 1400mAh Li-ion batteries that are to be connected in series so as to get resultant voltage of 14.8V and 1400mAH current rating....
5 replies -
Replied #Threads
line follower dc motors problem
silverscorpionHow much voltage are you giving the motors? And how much to the sensors? You might want to check if the sensors are working properly after...
-
Posted #Threads
line follower dc motors problem
Hi, I have made a line follower bot circuit consisting of AT89S52 MCU, 2 IR sensors with lm324 op-amp and l293d motor driver IC. My motor...
2 replies -
Posted #Threads
best book on 8051
please suggest some best books for learning 8051 assembly programming....
3 replies -
Posted #Threads
ISP for AT89S52
I want to make an ISP(In System Programmer) for AT89S52 Microcontroller. Can anyone provide me some links for complete info regarding this.😒
1 reply -
Replied #Threads
Learn Robotics-3 - Introductin to a Line Follower..
silverscorpionI think you're mistaken. If the width of the line is 20 cm, and the robot has to follow that line, then the width of the...
-
Posted #Threads
PCB schematic design
Can anyone tell me about any software for PCB schematic design that has the complete library of components. I have tried two software - Eagle 5.7.0...
12 replies -
Replied #Threads
l293d motor driver IC help
silverscorpionWell, I dont get your question.. What's the problem in giving two different voltages to 2 pins in the same IC?? Pins 1 and 9 (Enable...
-
Posted #Threads
l293d motor driver IC help
I am using L293D motor driver for line follower which has the following pin configuration- In this at Pin no. 8 we have to apply the...
5 replies -
Posted #Threads
Burning program on At89s52
hello, i am using AT89S52 in my project and i want to know how can i burn any program on it(i mean to know about the...
1 reply -
Posted #Threads
ir sensor circuit
please anyone provide me a working ir sensor circuit which can be used in line follower. i have tried about 5-6 circuits on breadboard i found...
-
Replied #Threads
problem in IR sensor circuit
just2rockyes check POT with preset value check & calculate 5k or so.reverse ploarity for IR D1 at OPAMP PIN6,same for against 100 ohm resistance...pls check resistance...
-
Replied #Threads
problem in IR sensor circuit
MuffyReverse polarity of receiver diode . The diode labeled "IR receiver D1" , connect the anode of diode to pin 6 of lm324 and the cathode...
-
Replied #Threads
problem in IR sensor circuit
Muffy@pratik20990 : Reverse bias the receiver diode, inter change the polarity . It should work. When ir is indecent on the diode the reverse leakage current...
-
Replied #Threads
problem in IR sensor circuit
reachrkataWhich is the IR receiver you are using? Can you give the part number? From what i understand from the circuit, you want to stop the...
-
Replied #Threads
problem in IR sensor circuit
one more thing my battery is getting heated up. is this normal?
-
Posted #Threads
problem in IR sensor circuit
i have made an IR sensor circuit on breadboard which is this- i made this circuit on breadboard and when powered it with 9V battery the...
13 replies -
Replied #Threads
problem in IR emitter detector circuit
bajause it with comparatorya i am using it with comparator IC 741 but i am confused about the connections to be made with the three legs...
Activity by month
Where pratik20990 contributes
-
#Threads 22 · 100%
Highlights
- Reactions per contribution
- 0.0
- Best answers
- 0
- Member for
- 17 years