maxz
@maxz-iHZPgv Member
- Member since
- Joined
- Last active
- Active
- Member number
- Member #32,630
- Posts
- 11
- Replies
- 37
- Reactions
- 0
- Active days
- 0
Contributions
Last 12 months
0 contributions
- Active days
- 0
- Longest run
- 0 days
- Current run
- 0 days
Trophies
Featured trophies
0 / 8
Swipe or scroll to see more trophies
-
Replied #Threads
Car Brake System~!!!! How to improve it?
well~ for my project, i just studies on the design of the braking plate and the material of it only. as i mentioned, no sponsors. so...
-
Replied #Threads
Car Brake System~!!!! How to improve it?
I see.... but i think there's some alternative way to use on the improvement.. since i graduated, i never look on the research already. Moreover, there...
-
Replied #Threads
Car Brake System~!!!! How to improve it?
Thank you again for all. I'm here and yes, i have graduated from my University.
-
Replied #Threads
Car Brake System~!!!! How to improve it?
Finally i had a break through and my project were a success. I had a Grade B on my Project and i'm very proud and thank...
-
Replied #Threads
Stress Analysis Using Autodesk Inventor 2010
Dear Juma... What happen with inventor 2010??? I do all the steps but i couldnt get wat u did in here... it shows only displacement and...
-
Replied #Threads
Stress Analysis Using Autodesk Inventor 2010
Omg Juma~!! U're really Helpful... and this thing i saw it before in Inventor.. and i was like wtf was this... so i doesnt care much...
-
Replied #Threads
Stress Analysis Using Autodesk Inventor 2010
thx juma~!! It would be appreciate if u write it step by step how to set those configurations.
-
Replied #Threads
Circular Plate Bending Moment and Stress
btw wat is design accelerator formulas??? where can i get it?
-
Replied #Threads
Stress Analysis Using Autodesk Inventor 2010
Dear Juma, I have roughly sketch the plate i wanted to analyst... I hope this could help for you, so that u could help me out...
-
Replied #Threads
Stress Analysis Using Autodesk Inventor 2010
I'll post the picture soon... allow to help me out.. thx so much~!!
-
Replied #Threads
Stress Analysis Using Autodesk Inventor 2010
Yesss... Juma~!! this is exactly wat i need... a displacement and stress analysis...
-
Replied #Threads
Circular Plate Bending Moment and Stress
For the manual calculation part i'm done, and the result is quite satisfied... But i need to compare it with my simulation testing using Inventor 2010......
-
Replied #Threads
Car Brake System~!!!! How to improve it?
it is possible if were to implement ABS to my design as well... Currently i were to test on the friction efficiency between existing and my...
-
Replied #Threads
Circular Plate Bending Moment and Stress
Dear Juma~!!! Your guides is very useful to me. being finding this for a long time. Never know it can be found in Autodesk Inventor Handbook....
-
Replied #Threads
COMSOL Error 7094???????
Thx alot... it help. yeah. my memory is out~!!! need to upgrade my Ram
-
Replied #Threads
Car Brake System~!!!! How to improve it?
No comments on my idea for the brake?????? wierd~!!!!
-
Replied #Threads
Car Brake System~!!!! How to improve it?
Its been a while i left this post death~!! I'm back and wanted to post some of the pictures in here. i Guess i will receive...
-
Replied #Threads
Car Brake System~!!!! How to improve it?
The shape would be on its way. currently i still stucking on my project idea. as my college have damn a lot of student were doing...
-
Replied #Threads
Car Brake System~!!!! How to improve it?
It is true. Increase Surface area for friction is much likely better than the existing 1. the existing area surface is limited. so i think is...
-
Replied #Threads
How would you modify a bicycle to make it more efficient?
Hurm~!!!! I think the body of the frame have to be mobs a bit by mobbing it with some angle to reduce the air frictions against...
-
Replied #Threads
Car Brake System~!!!! How to improve it?
Nah. Tat Info is from my crap supervisor telling that drum is more efficient. i disagree with him as well.. and ya magnectic brake have some...
-
Replied #Threads
Car Brake System~!!!! How to improve it?
Ok. I understand. So i maybe mistaken on the disc and drum brake. So its ok. But i got a doubt which Brake is better for...
-
Replied #Threads
Car Brake System~!!!! How to improve it?
Erm... actually i not agree on it too. But my Lecturer said that the drum brake is better than disc brake. Initially when i propose my...
-
Replied #Threads
Car Brake System~!!!! How to improve it?
Idea pops out on the Drum Brake. Since we know that Drum Brake is more efficient than Disc Brake. In 80's Drum brake is invented and...
Activity by month
Where maxz contributes
-
#Threads 48 · 100%
Highlights
- Reactions per contribution
- 0.0
- Best answers
- 0
- Member for
- 17 years